Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Amarillo Homeowners
Chimney problems in Amarillo rarely announce themselves. A hairline crack in the crown, a rusted damper, a cap that blew loose in a spring windstorm – these sit quietly until water gets behind the masonry or smoke starts backing into the living room. We repair all of it: crowns, flashing, caps, liners, and masonry, using professional-grade materials and the brands chimney professionals trust. Our technicians have up to 15 years of experience, and we handle a lot of second opinions for homeowners who’ve been told they need a full reline and want the evidence before they spend the money.
You get the sweep, the inspection, and the repair from one company, which closes the gap between finding a problem and fixing it. Most jobs we can turn around same-day. For a free estimate on chimney repair in Amarillo, call (888) 527-6071. We answer 24/7, with fast dispatch from 7am to 7pm.
Chimney Cap Installation
Chimney Cap Installation is the fitting of a protective cover over the flue opening, and it’s the cheapest insurance your chimney has. A good cap keeps rain out of the flue, stops birds and squirrels from nesting, and keeps downdrafts from pushing smoke back into the room. If your chimney has no cap at all, or you’ve heard scratching from the flue, this is the place to start.
We install Gelco and Famco caps sized to your flue and your climate. Cap installation typically runs $150-$450 depending on flue count, cap style, and how the top of the chimney is built. We set the cap on a proper masonry or steel base so wind doesn’t peel it off. For a quote on chimney repair in Amarillo, call (888) 527-6071.
Choosing the Right Cap
Single-flue, multi-flue, and custom caps each solve a different problem. A single-flue cap suits a standard fireplace chimney, while multi-flue designs cover several openings under one frame. We match the cap to the flue opening, not to whatever’s nearest the shelf.
Fitting and Sealing
A cap that fits poorly rattles in wind and lets water run down the outside of the flue. We anchor it to the crown and seal the edges so rain sheds away from the chimney, not into it. That matters more here than in wetter climates, where a bad seal tends to show up faster.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement means pulling a damaged or missing cap and setting a new one in its place. Replacing a cap is often cheaper than repairing it, especially when the mesh is crushed, the frame is bent, or the cap has rusted through. Amarillo windstorms and hail do a number on cheap caps, and once the mesh is open, animals and weather get in.
We replace caps with Gelco and Famco units built to take the summer heat. Replacement typically ranges from $200-$500, and a lot of that depends on whether the old cap was set in mortar, which takes more time to remove cleanly. We inspect the crown while we’re up there so a small masonry problem doesn’t ride along behind the new cap.
When Replacement Beats Repair
Bent frames, crushed mesh, and rust-through at the joints are all reasons to replace rather than patch. A cap that’s been patched twice usually fails a third time in the first summer gust that finds it. If the base is sound and only the screen is torn, we’ll tell you that straight.
Disposing of the Old Cap
Old caps can be heavy, and a rusted one can seize in the mortar bed. We remove it in a way that doesn’t crack the crown behind it, then take it away so you’re not hauling a chunk of steel off the roof yourself. It’s a small detail that saves you a real headache.
Chimney Liner Installation
Chimney Liner Installation is fitting a new flue liner inside the chimney to contain heat and combustion gases. A cracked or missing liner lets creosote reach the masonry and puts carbon monoxide where it shouldn’t be, which makes this the repair we flag fastest. If a previous contractor told you a reline is the only answer, we can look at whether HeatShield resurfacing will do the job instead.
We install DuraFlex and Olympia Chimney liner systems, custom-fit for standard and non-standard flue shapes. Liner installation typically runs $1,800-$4,500 depending on length, flue configuration, and liner type. HeatShield resurfacing can restore a damaged clay flue at a lower cost than full relining when the chimney qualifies. That’s a real saving on a lot of Amarillo chimney repair jobs.
Sizing the New Liner
The liner has to match the appliance, not just the flue. We measure the flue, check the appliance’s venting needs, and pick a system that drafts correctly. An oversized liner is as much trouble as an undersized one.
After the Liner Goes In
Once the liner is set, we confirm the connection at the appliance and sweep out any debris from the install. You get photos of the finished flue so you can see what you paid for. Nothing is recommended without camera evidence you can watch for yourself.
Chimney Flashing Repair
Chimney Flashing Repair fixes the metal that seals the chimney to the roof, which is where most chimney leaks start. Flashing sits in a harsh spot: sun on one side, rainwater running down the other, and a constant push-pull as the chimney and roof move differently. When it fails, water shows up as a stain on the ceiling after a rain.
We reset or replace flashing with durable metal, sealing the joints against the masonry and the shingles so water can’t find a path behind it. Flashing repair typically runs $250-$700 depending on pitch and how the existing shingles interlock with the flashing. We always check the flashing when we’re on the roof for a sweep or cap job – it’s the leak we see most often.
Spotting a Leak Source
Ceiling stains don’t always mean the flashing is the culprit. Roof line, masonry cracks, and a failing crown can all send water to the same spot. We look at the whole top of the chimney before we commit to a fix, so we’re not charging you to seal the wrong joint.
Metal and Sealing Choice
The wrong metal reacts with the masonry or corrodes, and the wrong sealer peels within a season. We use materials matched to your chimney and your roof, not a default. It’s a small choice that decides whether the fix lasts.
Chimney Crown Repair
Chimney Crown Repair addresses the concrete or mortar top that sheds water off the chimney. The crown is the chimney’s first defense against rain, and a cracked crown lets water into the masonry, which shows up as efflorescence, rusting damper hardware, and interior leaks. Any crack wide enough to catch a fingernail is worth fixing.
We repair crowns by cleaning out the crack, filling it with a flexible repair material, and rebuilding the slope so water actually runs off. Crown repair typically runs $300-$900 depending on the size of the chimney and how much of the crown is damaged. A crown that’s cracked through in several places usually needs rebuilding rather than patching.
Why Crowns Fail Here
The Amarillo sun bakes the concrete on the chimney top through summer, and a crown that wasn’t sloped right from the start takes on water. A small crack grows through the next round of weather. Patching beats rebuilding when the slope is sound.
Rebuild vs. Repair
If more than a third of the crown is compromised, rebuilding the whole top is often the better buy. We explain both paths and what each costs, then let you choose. We won’t upsell a rebuild you don’t need, and we’ll tell you plainly when patching is enough.
Chimney Repair Companies
Chimney Repair Companies in this market range from dedicated chimney specialists to general handyman outfits that take on a chimney now and then. The difference matters when the job needs a liner, crown rebuild, or HeatShield resurfacing, because a handyman can reattach a flashing but can’t do a safe liner job. Hiring a specialist also means the person who found the problem can fix it.
We handle sweeping, inspection, and repair under one roof, using professional-grade brands like DuraFlex, Olympia Chimney, and HeatShield. Chimney repair work typically runs $150 to $4,500 across common repairs, so it pays to get a written estimate before anyone starts. Inspection without repair capability is just paperwork.
What to Ask Before Hiring
Ask whether they sweep and inspect as well as repair, and whether they’ll show you camera photos of the flue. Ask for a written estimate that itemizes each repair rather than a single lump sum. A specialist answers those questions without a sales pitch.
Red Flags in a Quote
A quote that demands a full reline with no camera evidence is the one to question. So is a repair estimate with no itemized line items. You’re allowed to ask for the photos and to call a second specialist – we’re happy to be the second opinion.
Chimney Masonry Repair
Chimney Masonry Repair covers the brick and mortar work on the chimney itself, including repointing joints, replacing spalled brick, and rebuilding a crown that’s gone too far. Mortar erodes over time and water gets into the joints, and once brick faces start flaking off, the chimney loses strength. This is the kind of repair that’s cheaper done early.
We match mortar to the existing brick so the repair doesn’t stand out, and we use Copperfield masonry products for the work that calls for them. Masonry repair typically runs $400-$2,500 depending on how much needs repointing and whether brick replacement is involved. We start with a camera inspection of the flue and a look at the exterior so you see the full picture before we quote.
Repointing vs. Rebuilding
Repointing restores the joints when the brick itself is sound, and it’s the cheaper path. Rebuilding a section is for spalled brick, cracked shoulders, or a chimney that’s leaning. We tell you which one your chimney actually needs and why.
Matching Mortar and Brick
Mortar that’s harder than the surrounding brick causes the brick to spall instead of the joint. We match the mortar mix and the brick face so the patch ages with the chimney. The repair should look like it was always there.
Brands We Service
We install and service DuraFlex and Olympia Chimney liner systems and know where each one wears out. DuraFlex flexible liners handle offsets in standard and non-standard flues well, and Olympia Chimney systems cover both standard relines and appliance-specific venting. Our technicians have up to 15 years of experience with both, so the fit and the draft are checked from the start.
We also work with HeatShield for liner resurfacing, which restores a damaged flue without the cost of a full reline when the chimney qualifies. Gelco and Famco cap and venting components make up the top-of-chimney side of our product mix, and Copperfield covers masonry repair. Whether you have DuraFlex, Olympia Chimney, HeatShield, Gelco, Famco, or Copperfield or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke backing into the room. Smoke that rolls out of the fireplace instead of up the flue usually means a blocked or damaged flue. It’s also a sign of incomplete combustion, which is a safety issue rather than just a nuisance.
- Water stains on the ceiling or chimney breast. Stains after a rain point to flashing, crown, or masonry letting water in. The longer it runs, the more the masonry absorbs, and the repair grows.
- White chalky staining on the brick. Efflorescence means water is moving through the masonry and carrying salts to the surface. It’s not dangerous on its own, but it tells you water is getting in somewhere.
- Cracked or flaking crown or mortar joints. Cracks in the crown or eroded joints let water into the chimney body. These are the repairs where early work saves real money later.
- Scratching, chirping, or birdsong from the flue. Animals in the flue block the draft and bring nesting material close to a heat source. A cap fixes the cause; a sweep clears the flue.
If any of these sound familiar, a camera inspection will tell you what’s actually happening. Call (888) 527-6071 to book one.
Our Process, Step by Step
- 1
We book the visit and confirm the scope. You tell us what you’ve noticed, whether it’s smoke, a leak, or a report from another contractor. We set a time that works and ask a few questions ahead of the visit so we arrive with the right tools.
- 2
We sweep and inspect the flue. A camera goes down the flue so we can see the liner, the joints, and the smoke chamber. The inspection is part of the visit, not a separate sales pitch, and we photograph anything we flag.
- 3
We walk you through the findings. You see the photos on screen, and we explain what each one means in plain terms. If a repair can safely wait, we say so, because not every crack needs work this month.
- 4
We write the estimate per job. Each repair gets its own line with the materials and the labor so you can see where the money goes. The written estimate sets the final price, and there are no add-ons after the fact.
- 5
We do the repair and confirm the result. The same company that found the problem fixes it, and we check the flue again after the work is done. You get photos of the finished repair so you know what changed.
How Much Does Chimney Repair Cost in Amarillo?
A typical cap installation in Amarillo runs $150-$450, flashing repair runs $250-$700, and crown repair runs $300-$900. Liner resurfacing or installation is the big-ticket item at $1,800-$4,500, and masonry repointing sits in the $400-$2,500 range depending on scope. Those ranges are estimates for common jobs, not a quote for yours.
Several things move the price. Flue count and configuration matter on liners, because a non-standard flue takes a custom-fit system rather than a standard length. Access is another factor: a steep roof line or a chimney set back from the ridge adds time to the job. Material choice matters too, since a full liner install runs higher than HeatShield resurfacing where the chimney qualifies for it. Masonry repairs get more expensive as more brick is involved, which is why we look at repairs early.
Getting a fair price starts with a written estimate that itemizes each repair rather than one lump sum. Ask what’s included: sweep, camera inspection, materials, and cleanup should each be covered. We don’t recommend work without camera evidence you can see, and we’ll tell you when a repair can safely wait.
Here’s a quick comparison of typical ranges:
| Repair | Typical Range |
|---|---|
| Cap installation or replacement | $150-$500 |
| Flashing repair | $250-$700 |
| Crown repair | $300-$900 |
| Masonry repair | $400-$2,500 |
| Liner installation or resurfacing | $1,800-$4,500 |
Call (888) 527-6071 for an exact quote. Estimates are free.
Our Service Area Near Amarillo
We cover Amarillo and the towns around it: Canyon, Rockwell Place, Bushland, Timbercreek Canyon, Lake Tanglewood, Claude, Panhandle, Happy, and Fritch. Response times vary with distance and traffic, but most of the metro is same-day. For homeowners west of town, we also handle chimney repair in Canyon, and our Chimney Sweep Amarillo page explains how the sweep visit fits with a repair. Customers east of the city often book chimney repair in Rockwell Place through the same dispatch, and our chimney repair page covers the full scope of what we fix.
Serving Amarillo, TX – Our Local Coverage Area
We serve Amarillo and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Amarillo
Chimney repair is the work of fixing the parts of the chimney that have worn, cracked, or failed, including the crown, flashing, cap, liner, and masonry. It’s distinct from a sweep, which clears creosote, and from an inspection, which identifies problems with a camera. Repairs happen after the inspection flags them, and we handle all three so the findings and the fix come from one company. Call (888) 527-6071 to book a repair visit.
Most small repairs, like a cap, a flashing reset, or a crown patch, take a couple of hours on site. Masonry repointing and liner installation are longer jobs, often a full day or more depending on the chimney. We give you a time estimate with the written quote so you can plan around it. Call (888) 527-6071 for a schedule and an exact quote.
Common chimney repairs in Amarillo range from about $150 for a cap to $4,500 for a full liner install, with most single repairs landing between $250 and $900. Crown, flashing, and masonry work sit in the middle of that range, while liner work is the high end. The written estimate sets the final price, and repairs that can safely wait are marked as such. Call (888) 527-6071 to book a free estimate.
Yes, we install and service DuraFlex and Olympia Chimney liner systems and match the liner to your flue and appliance. We also work with HeatShield for liner resurfacing when the chimney qualifies, which can save on a full reline. Our technicians have up to 15 years of experience with these systems. Call (888) 527-6071 to have your flue checked.
Same-day service is often possible depending on the day’s schedule and what the repair involves. We answer 24/7, with fast dispatch from 7am to 7pm. A call outside dispatch hours is booked into the next opening, Sunday through Friday. Call (888) 527-6071 to book a visit.
We stand behind the work we do, and the warranty terms are confirmed with your written estimate so you know what’s covered before anyone starts. Different repairs carry different coverage, and we tell you which applies to yours. Ask about it when we walk through the findings. Call (888) 527-6071 with any warranty questions.
Clear the area around the fireplace and the hearth so we have room to work, and move anything breakable off the mantel. If you have pets, keep them clear of the work area while we’re on site. If you have a report or photos from another contractor, have them ready so we can compare findings. Call (888) 527-6071 to confirm your booking and ask anything else.
Schedule Your Chimney Repair Service in Amarillo Today
If a crown crack, a loose cap, or a report from another contractor has you wondering what really needs fixing, one call gets you a straight answer with photos to back it up. We sweep, inspect, and repair from the same company, using professional-grade materials. Call (888) 527-6071 for a free, no-obligation estimate. We answer 24/7, with fast dispatch from 7am to 7pm. If you’d like to start with the inspection side first, a chimney inspection or a chimney sweep is the right first step.
Written by the team at Chimney Sweep Amarillo.